Who should attend our courses ?
We are providing complete services for qualification of engineering personnel. Our trainings and personnel qualifications are mainly focused on the following positions:
- NDT (non-destructive testing) – certification of NDT personnel
- corrosion engineers
- Designers and Production technologists
- inspectors and supervizors in industrial facilities
- welding personnel
- technical education for executive staff, middle and top management
- re-qualification Recertification programs
Why you should be trained?
Due to a continual tendency to rise efficiency and productivity, the demand on personnel qualification is also increasing. Company, which needs to build a good position on the market, needs also continual personnel education
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 6 days
- Overall hourly volume: 40 hours
- Theorical reception capacity: 12
Training goals:
- Adjust tools
- Putting ultrasonic testing into practice
validation:
A NIv I qualification certificate for the Ultrasonic control method will be issued at the end of the Training
Main modules:
- General information on the control technique
- Technical knowledge
- Verification of equipment
- Development and interpretation
- Definition of levels
- Presentation of standards, codes and procedures
- Classification of defects
- Control and interpretation
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 6 days
- Overall hourly volume: 40 hours
- Theorical reception capacity: 12
Training goals:
- Adjust tools
- Put into practice ultrasonic checks according to written instructions on simple parts adjust equipment
- Define ultrasonic inspection conditions
- Apply acceptance criteria
- Examine various parts, apply acceptance criteria
- Provide a control report
validation:
A NIv II qualification certificate for the Ultrasonic control method will be issued at the end of the training
Main modules:
- General information on the control technique
- Basic principle
- Application domain
- Technical knowledge
- Introducing Ultrasonic Grades
- Presentation of the material
- Presentation of the reference blocks
- Presentation of standards, codes and procedures
- Operating mode
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 6 days
- Overall hourly volume: 40 hours
- Theorical reception capacity: 12
Training goals:
- Acquire the technical knowledge relating to the use of X-ray and gammagraphy techniques
- Exercising control according to specific instructions
- Check radiograms
validation:
A NIv I qualification certificate for the X-ray control method will be issued at the end of the training
Main modules:
- Introduction
- Shooting techniques
- Image quality indicators
- Development and interpretation
- Preparation of parts
- Use of equipment and films
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 6 days
- Overall hourly volume: 40 hours
- Theorical reception capacity: 12
Training goals:
- Acquire the technical knowledge relating to the use of X-ray and gammagraphy techniques
- Exercising control according to specific instructions
- Interpret films
- Prepare a control report
validation:
A NIv II qualification certificate for the X-ray control method will be issued at the end of the Training
Main modules:
- Introduction
- Operating mode
- Shooting techniques
- Image quality indicators
- Development and interpretation
- Use of equipment and films
- Interpretation of radiograms
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 3 days
- Overall hourly volume: 18 hours
- Theorical reception capacity: 12
Training goals:
- Practice non-destructive testing by magnetic particle inspection according to specific written instructions
- Identify and classify the indications highlighted by magnetic particle inspection
- Write a control report.
validation:
A NIv I qualification certificate for the magnetic particle inspection method will be issued at the end of the training
Main modules:
- Introduction
- Shooting techniques
- Image quality indicators
- Development and interpretation
- Preparation of parts
- Use of equipment and films
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 3 days
- Overall hourly volume: 18 hours
- Theorical reception capacity: 12
Training goals:
- Practice non-destructive testing by magnetic particle inspection according to specific written instructions
- Identify and classify the indications highlighted by magnetic particle inspection
- Examine the results, apply the acceptance criteria, assess the conformity of the parts checked
- Write a control report
validation:
A NIv II qualification certificate for the magnetic particle inspection method will be issued at the end of the training
Main modules:
- Principle of magnetic particle inspection
- Implementation of the magnetic particle method
- Measurement, influence of the nature of the current on the detection of faults
- Operating mode
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 3 days
- Overall hourly volume: 18 hours
- Theorical reception capacity: 12
Training goals:
- Acquisition of the basic knowledge necessary for penetrant testing
- Identify and classify PT indications
- Write a control report.
validation:
A NIvI qualification certificate for the Penetrant Testing method will be issued at the end of the Training
Main modules:
- General information on non-destructive testing. Technical knowledge
- Application domain
- Hot Penetrant
- Cold penetrant testing
- Limits of the method
- Elements of choice of an appropriate penetrant testing range
- Interpretation of results
- Entry level: 4AM, 3AS or 3 years experience
- Duration of training: 3 days
- Overall hourly volume: 18 hours
- Theorical reception capacity: 12
Training goals:
- Acquisition of the basic knowledge necessary for penetrant testing, Written instructions
- To allow the choice of techniques and products as well as the realization of the control, the evaluation and the interpretation of the controlled parts
- Write a control report
validation:
A NIv II qualification certificate for the Penetrant Testing method will be issued at the end of the training
Main modules:
- General information on the control technique
- Technical knowledge
- Penetrant testing on various parts
- Metallurgical defects
- Presentation of standards, codes and procedures
- Preparation of surfaces to be examined
- Types of pipes to use
VT is the most widely used non-destructive material testing (NDT) method. The method is focused on detecting and evaluating the condition (properties) of the surfaces of products or components with the naked eye or with the help of special devices or equipment. The VT method is used in classic NDT inspection, when we look for defects such as cracks, inflammation, surface pores, we also detect shape deviations – we measure and evaluate linear displacement, the elevation of the root of the weld, the displacement of forms in the casting, and we also check the surface condition. It is an NDT method that is full-fledged compared to other NDT methods (e.g. RT, PT, …) and in its scope even exceeds the scope of the use of other NDT methods, it is considered a basic NDT method that should be performed before any other NDT method.
Principle of method:
Visual inspection is performed on the prepared (cleaned, degreased and dried) tested surface of the part. As a result, the quality of this preparation affects the achievable sensitivity of the test – the identifiability of defects. The success of the exam depends on the fulfillment of three basic attributes – these are:
- visual ability of the worker performing the tests
- the condition of sufficient illumination of the tested surface
- professional competence – knowledge and practical skills of the worker conducting the VT examinations
The inspection can be carried out directly by sight without aids, further with the use of basic aids such as mirrors, gauges, gauges, magnifiers, etc., possibly using endoscopes and other special devices. In recent years, the demand for performing visual examinations using endoscopes (borescopes, fiberscopes, videoscopes) has become more and more significant. Typical applications appear especially in the field of aviation (during operational inspections), in the energy sector (inspection of reservoirs, exchangers, pipelines, ..), but also in production – e.g. welded frames, closed profiles, etc.
We provide courses for Level I, II and III workers. We belong to the most important trainers of “special processes” in Europe. The preparation and qualification of the test staff is carried out according to the standards
- ISO 9712
- ISO 9712 – VT2dw
- VT of welds (according to ATG G19-32.2)
- EN 4179 for the aviation industry – JAR 145.30
- SNT-TC-1A
Leakage testing is aimed at detecting imperfections in the solid interface, which allows fluids to penetrate due to the pressure drop between the two surfaces. In general, it is possible to detect material defects (caused by imperfection of the metallurgical or technological process or during operation), mechanical joints and non-detachable joints (welds, glued and soldered joints).
The size of the leak is then given by the volume of substances that penetrated the defect per unit of time. In principle, two basic types of tests are distinguished – integral (to determine the total value of the size of the leak) and localization (aimed at determining the location of the leak).
Test methods/techniques:
- Micro-flow measurement method (overpressure/vacuum)
- Pressure change method (decrease/increase in pressure, overpressure of liquid, gas, …)
- Bubble method (positive pressure, negative pressure with a vacuum chamber)
- Capillary method (seepage of penetrant through the tested object)
- Helium method (test gas – He, design – overpressure, vacuum, …)
- And others (ultrasound scanning, …)
The choice of a suitable testing method and technique depends on the required sensitivity of the test, on the nature of the tested part (shape, its construction, size (volume)), on legislative requirements, customer requirements.
The methodological requirements for the LT test are – they prescribe standards, codes, regulations and customer requirements.
LT testing according to EN requirements is based on the following standards
- EN 1518 – Characterization of leak detectors based on the principle of mass spectrometers
- EN 1593 – Bubble method
- EN 1779 – Criteria for the selection of methods and procedures
- EN 13184 – Pressure change method
- EN 13185 – Test gas method
- EN 13192 – Calibration of reference leaks for gases
- EN 13625 – Guidelines for the selection of instruments for measuring gas leakage
The most important and required LT standards and specifications from the field of US standards are ASTM E 1003 (hydrostatic tests), ASTM E 515 (bubble method), ASTM E 493, 498, 499, 1066 (mass spectrometer), ASME Code and others.
We provide courses for Level I, II and III workers. We belong to the most important trainers of “special processes” in Europe. The preparation and qualification of the test staff is carried out according to the standards
- ISO 9712 – technique LT C (trace gases) or LT B (bubble method)
- EN 4179/ NAS 410 for the aerospace industry – JAR 145.30
- LT L2 HS (“water law”) – suitable for audit firms that need to meet the requirement of Decree No. 175/2011 Coll.
- SNT-TC-1A
The courses are focused on leak testing and evaluation of findings using all the methods/techniques described above (courses for the scope of PCT + BT + PT – qualification general, qualification field MS-B and practice for MS-B) or using tracer gas methods (course qualification general , MS-C qualification field course and internship for MS-C).
We provide professional courses for IRT (and all other NDT methods) for operators Level I, II and III. We belong among the most important trainers of “special processes” in Europe.
Training and qualification of the NDT personnel is in accordance with the following standards
- EN 4179 / NAS 410 for aerospace industry – JAR 145.30 (customers’ specifications as NDT manual of Boeing 737, Airbus A310, Airbus A318 – A321 etc. are part of the lecture)
- SNT-TC-1A
- ISO 11484, EN 10256 (for testing of tubes and pipes)
- ISO 9712, including qualification for PED (pressure vessels)
we provide courses for Level I, II and III workers. We belong to the most important trainers of “special processes” in Europe. The preparation and qualification of the test staff is carried out according to the standards
- ISO 9712 – technique LT C (trace gases) or LT B (bubble method)
- EN 4179/ NAS 410 for the aerospace industry – JAR 145.30
- LT L2 HS (“water law”) – suitable for audit firms that need to meet the requirement of Decree No. 175/2011 Coll.
- SNT-TC-1A
The courses are focused on leak testing and evaluation of findings using all the methods/techniques described above (courses for the scope of PCT + BT + PT – qualification general, qualification field MS-B and practice for MS-B) or using tracer gas methods (course qualification general , MS-C qualification field course and internship for MS-C).
We organize courses for NDT personnel Level I, II and III in our training centers. ATG is one of the most important training centers of the “special processes” in Europe.
All courses for NDT personnel – Level I, II and III are organized at our training centres.
Training and qualification of the NDT personnel is in accordance with the following standards
- ISO 9712, EN 10256
- EN 4179/NAS 410 for aerospace industry (“JAR 145.30”)
- SNT-TC-1A for pressure vessel industry, testing according to ASME Code, ASTM, MIL aj.
we provide courses for Level I, II and III workers. We belong to the most important trainers of “special processes” in Europe. The preparation and qualification of the test staff is carried out according to the standards
- ISO 9712 – technique LT C (trace gases) or LT B (bubble method)
- EN 4179/ NAS 410 for the aerospace industry – JAR 145.30
- LT L2 HS (“water law”) – suitable for audit firms that need to meet the requirement of Decree No. 175/2011 Coll.
- SNT-TC-1A
The courses are focused on leak testing and evaluation of findings using all the methods/techniques described above (courses for the scope of PCT + BT + PT – qualification general, qualification field MS-B and practice for MS-B) or using tracer gas methods (course qualification general , MS-C qualification field course and internship for MS-C).
